QRZ.COM
ad: MyAnt-1
ad: L-HROutlet
ad: l-rl
ad: Subscribe
ad: l-assoc
JS1KSU Japan flag Japan

Login is required for additional detail.

QSL: BURO OR DIRECT

Email: Login required to view

XML Subscriber Lookups: 9463


Welcome to my page ! 

      

I'm using "Super Rad Antenna" for mobile.

My blog         : http://blogs.yahoo.co.jp/djgpj817

My facebook : https://www.facebook.com/minoru.kosuge.73

My position   : APRS   ( JS1KSU-5 )

IC-7300 by ICOM

SUB BATTERY

Super Rad Antenna lineup

My weblog : http://blogs.yahoo.co.jp/djgpj817

My facebook : https://www.facebook.com/minoru.kosuge.73

Go top

 

 

About my QTH            

My QTH Hiratsuka beach.                                       

Cherry Blossom  (  April  )

Japanese autumn. We enjoy sightseeing colored leaves red & yellow. (HAKONE November)

"JINGU-GAIEN" in TOKYO  ( November )

Mt FUJI from my QTH

Hiratsuka beach with surfer  ( February )

Mt HAKONE from Hiratsuka beach  ( February )

Mt FUJI from Hiratsuka beach  ( February )

Go top

 

 

I like DX vacation.      

New Caledonia  January 2018

Guam island  February 2016                                           

Thailand  January 2015  "HS0AC"   I operated a radio from Thailand. ( Asian Institute of Technology )

Big Antenna HS0AC in AIT ( Asian Institute of Technology )

Guam island  January 2013

Saipan island  February 2012

Guam island  February 2011

Guam island  September 2009

My weblog : http://blogs.yahoo.co.jp/djgpj817

My facebook : https://www.facebook.com/minoru.kosuge.73

Go top

 

 

My other hobby "Windsurfing"    

Go top

 

 

My HAM friends       

FK4RD Yves, JS1KSU, FK1UW Goulven, 

                FK8DD Sam, FK8IK Mic

Ray  KH2GUM                              Danny  KH2JU

  

Freddy  JD1BOX/F4HEC                             Jack   HS1FVL

  

Tariq    N2QV                                          Paul   VK3SS

  

Champ   E21EIC                                      Matt

  

Mustapha   DL1BDF                                  Franz   DJ9ZB

  

K3LP   David  (Silent Key)  Rest In Peace    

Go top

 

 

How to make the ”Super Rad Antenna” for 15m BAND                          

Parts                                                               

1) case for waterproof 60mm X 280mm ( PVC )

2) bobbin( VU-40 ) 48mm X 250mm ( PVC )

3) mast ( VP-25 ) 30mm X 250mm ( PVC )

4) joint( 25 x 40 ) ( PVC )

5) joint ( 13 x 25 ) ( PVC )

6) cap ( VU-50 ) ( PVC )

7) guide for coil

8) coaxial cable5D-2V x 50cm

9) a terminal

10) tapping screw 4mm x 15mm

11) a sheetof aluminum 0.2mm x 100mm x 180mm

12) a connector M-type for 5D

13) an electric wire ( 2-square )

14) copper wire

The manufacture of a connector

Make a bobbin

 

1) Tuning

The making is easy, but the perseverance is necessary for an adjustment. An antenna analyzer is necessary. An adjustment puts two stages of resonant frequency together first and next does a SWR adjustment.

I  A main coil is wound it than the purpose frequency.

  (If it's 21MHz, for example it'll be about 19 turn, so it's made with 20 turn.)

II  I think it'll be 18-about 20 MHz when I search an analyzer for a resonance point. The upper side of the coil (the cylinder side).

I see 2-3 cm will be cut down, and how long a frequency rises. I see how long to rewind by its change amount, but you aren't supposed to rush. I'll go a little slowly.

(Please take a ground for an analyzer. If it's an element, a meter doesn't become stable by a body effect. Please don't worry about SWR at the same time.)

III  An interior adjustment can be done to II, but it becomes real from here in an adjustment by the used society. When it's taken out on the table, a resonance point falls. When I cover an antenna with a waterproof case again, it falls again. There is occasionally a case that I cut a coil too much and go from the purpose frequency to the top. An aluminum kitchen tape will be stuck on the cylinder upper part a little at that time. A resonance point falls by increasing the capacity.

  (Even if it's spread inside the bobbin, the aluminum tape is OK.)

IV  It's a SWR adjustment at the end, but this is performed at the top and the bottom of the link coil. I think the best point will be found immediately. If a resonance point slips by moving a link coil, please adjust it by fluctuation of an aluminum tape. It's fixed by a vinyl tape so that a link coil doesn't move.

 

2) waterproof treatment

When using it experimentally, I don't mind by a nude condition, but waterproof treatment is needed to be established. When the waterproof treatment is made a nude condition, then a resonant frequency changes. When a waterproof case gets wet with rain, a resonant frequency falls. So the band used actually has, and I'd hope that you establish a resonance point. For example I have mixed around the 21.280MHz in case of 21MHz. SWR less than 1.5 fits into about 21.330 MHz from 21.230MHz with this, but when I get wet with rain, 50KHz falls. 260KHz will be to be able to go out from the 250KHz I wish both.

My weblog : http://blogs.yahoo.co.jp/djgpj817

My facebook : https://www.facebook.com/minoru.kosuge.73

Go top  

 

 

8658277 Last modified: 2018-02-18 02:03:51, 15349 bytes

Login Required

Login is required for additional detail.

You must be logged in to file a report on this page

Please login now...

Public Logbook data is temporarily not available for this user
ad: giga-db
Copyright © 2018 by QRZ.COM
Sun Feb 18 20:13:12 2018 UTC
CPU: 0.050 sec 73035 bytes mp